收藏本站

ADP1653
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
SETT 1
SETF 2
CTRL1/SCL 3
CTRL0/SDA 4
PIN 1
INDICATOR
ADP1653
TOP VIEW
(Not to Scale)
12 PGND
11 INT
10 INTF
9 HPLED
Figure 4. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
SETT
SETF
CTRL1/SCL
CTRL0/SDA
SETI
ILED
OUT
GND
HPLED
INTF
INT
PGND
LX
V DD
EN
STR
Description
Set Torch Input (2-Bit Logic Interface Only). SETT programs the high power LED current in torch mode. An
external resistor connected between SETT and ground sets the torch current. When SETT is tied high, the current
is internally set to 125 mA. In I 2 C mode, this pin is regarded as a no connect.
Set Flash Input. SETF programs the high power LED (HPLED) current in flash mode and allows for transmit
blanking of the LED. In 2-bit logic interface mode, an external resistor connected between SETF and ground sets
the flash current. If SETF is tied high, the current is set internally to 500 mA. In I 2 C mode, the flash current scales
with both the external resistor and the internal HPLED bits in the output select register. If SETF is tied high, an
internal 50 kΩ resistor combined with the HPLED bits set the HPLED current.
Serial Interface Clock Input. In 2-bit logic interface mode, CTRL1 is the second input bit of the digital interface.
In I 2 C mode, SCL is the clock input of the I 2 C-compatible serial interface.
Serial Interface Data Input. In 2-bit logic interface mode, CTRL0 is the first input bit of the digital interface.
In I 2 C mode, SDA is the data input/output of the I 2 C-compatible serial interface.
Set Indicator Input (2-Bit Logic Interface Only). SETI programs the indicator LED current. An external resistor connected
between SETI and ground sets the indicator LED (ILED) current. If SETI is tied high, the current is internally set to
10 mA. In I 2 C mode, this pin is regarded as a no connect.
Indicator LED Input. Connect the cathode of the indicator LED to the ILED pin. Connect the anode to the battery
or to a voltage rail greater than the LED forward voltage.
White LED Output Voltage. OUT senses the output voltage of the white LED step-up converter. At startup, the
ADP1653 limits the rate of increase of the voltage at OUT (soft start) to prevent excessive input inrush current.
The OUT pin features a comparator to detect an overvoltage condition if the LED string is open circuited. Connect
the anode of the white LED(s) to OUT. Connect a 3.3 μF or greater capacitor between OUT and PGND.
Analog/Digital Ground. Connect GND to PGND at the LFCSP paddle.
High Power LED Current Regulator. HPLED regulates the current of the high power LED(s). Connect the cathode of
the white LED string to HPLED.
Interface Input. INTF selects the 2-pin interface mode. INTF is driven high to enable CTRL1 and CTRL0 for 2-bit
logic interface mode. INTF is driven low to enable SDA and SCL for I 2 C interfacing.
Active Low Interrupt Output. INT is an open-drain output that transitions from high to low to signal that a fault
condition has occurred. INT should be connected via a pull-up resistor (for example, 10 kΩ to 100 kΩ) to the I/O
supply rail and directly to the system processor. When an interrupt is detected, the system processor can read the
FAULT register, using the I 2 C interface for details on the fault condition.
Power Ground for Internal Switching FET.
White LED Switch Node. LX drives the inductor of the white LED step-up converter. An inductor and diode
connected to LX powers the white LEDs.
Supply Input. Connect the battery between V DD and PGND. Bypass V DD to PGND with a 4.7 μF or greater capacitor.
Enable Input. CMOS input. Driving EN high turns on the ADP1653. Driving EN low disables the ADP1653 and
reduces the input current to less than 1 μA. When EN is high, disabling the LEDs puts the part into sleep mode,
dropping the input current to less than 45 μA.
Strobe Control Input (I 2 C Interface Only). CMOS input. Driving STR high enables the flash function of the white
LED. STR also enables the watchdog timer to prevent overstressing the white LEDs.
Rev. B | Page 7 of 24
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ADP1712-EVALZ BOARD EVALUATION ADP1712
ADP1720-EVALZ BOARD EVAL FOR ADP1720-ADJ
ADP2140CPZ-REDYKIT REDYKIT 2 BOARDS ADP2140ACPZ
ADP3110AKRZ-RL IC MOSFET DRIVER DUAL 12V 8SOIC
ADP3120AJCPZ-RL IC MOSFET DRIVER DUAL 12V 8-DFN
ADP3121JRZ-RL IC MOSFET DRIVER DUAL 12V 8SOIC
ADP3415LRMZ-REEL IC MOSFET DVR DUAL BOOTST 10MSOP
ADP3419JRM-REEL IC MOSFET DVR DUAL BOOTST 10MSOP
相关代理商/技术参数
ADP1653ACPZ-R71 制造商:AD 制造商全称:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface
ADP1653-EVALZ1 制造商:AD 制造商全称:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface
ADP1655 制造商:AD 制造商全称:Analog Devices 功能描述:Dual LED Flash Driver with I2C-Compatible Interface
ADP16550001ACBZR 制造商:Analog Devices 功能描述:
ADP1655ACBZ-R7 功能描述:IC LED DRVR BKLGT FLASH 12-WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
ADP1655-EVALZ 功能描述:BOARD EVAL ADP1655 RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD
ADP165ACBZ-1.2-R7 功能描述:Linear Voltage Regulator IC Positive Fixed 1 Output 1.2V 150mA 4-WLCSP (0.97x0.97) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 稳压器拓扑:正，固定式 电压 - 输出:1.2V 电流 - 输出:150mA 电压 - 跌落（典型值）:- 稳压器数:1 电压 - 输入:2.2 V ~ 5.5 V 电流 - 限制（最小值）:215mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UFBGA，WLCSP 供应商器件封装:4-WLCSP（0.97x0.97） 标准包装:3,000
ADP165ACBZ-1.8-R7 功能描述:Linear Voltage Regulator IC Positive Fixed 1 Output 1.8V 150mA 4-WLCSP (0.97x0.97) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 稳压器拓扑:正，固定式 电压 - 输出:1.8V 电流 - 输出:150mA 电压 - 跌落（典型值）:- 稳压器数:1 电压 - 输入:2.2 V ~ 5.5 V 电流 - 限制（最小值）:215mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UFBGA，WLCSP 供应商器件封装:4-WLCSP（0.97x0.97） 标准包装:3,000